Wood pellets look simple, but turning loose sawdust into a hard, glossy fuel that burns cleanly takes a carefully controlled process. Here is how wood pellets are made in a modern factory – and what each stage means for the quality you receive.
1. Selecting the raw material
Most heating pellets are made from clean wood residues: sawdust, shavings and chips from sawmills and wood processing, as well as low-grade logs. The raw material decides much of the final quality. Bark, sand and soil raise ash content, while clean debarked wood produces premium pellets. Softwoods such as pine are popular because their natural lignin content helps bind the pellet.
2. Debarking and chipping
When logs are used, they are debarked and chipped into small pieces. Removing bark and stones at this stage is one of the most important steps for keeping ash below the 0.7% A1 limit.
3. Drying to the right moisture
Fresh wood can contain 40–55% water. Before pressing, the material is dried in a rotary or belt dryer to around 10–12% moisture. Too wet and the pellets will be soft and crumble; too dry and they will not bind and may scorch in the die. Finished pellets usually leave the line below 10%.
4. Hammer milling
Dried material passes through a hammer mill that grinds it into a uniform particle size, usually smaller than the pellet diameter. Even particle size means even compression and a consistent pellet.
5. Conditioning
Some producers add a small amount of steam or water to condition the material. This softens the natural lignin so it can act as a glue during pressing. Premium pellets do not need chemical binders – lignin does the job.
6. Pelletizing
This is the heart of the process. A pellet mill forces the material through holes in a thick steel ring or flat die using heavy rollers. The pressure and friction heat the wood to roughly 90–120 °C, the lignin melts and the pellet comes out hard and shiny. Knives cut the strands to length.
| Stage | Main goal | Quality impact |
|---|---|---|
| Raw material | Clean wood, no bark/soil | Ash content |
| Drying | 10–12% moisture | Durability, heat value |
| Milling | Uniform particles | Consistent density |
| Pelletizing | High compression | Hardness, gloss, low dust |
| Cooling & screening | Stable, dust-free pellets | Fines < 1% |
7. Cooling and screening
Hot pellets are soft. A counter-flow cooler brings them close to ambient temperature, which hardens them. They are then screened to remove fines (dust and broken pieces), which are returned to the line. This is why quality pellets have very little dust in the bag.
8. Bagging and storage
Pellets are packed in sealed polyethylene bags (often 15 kg), in big bags of around one tonne, or loaded in bulk. Sealed bags protect against moisture, which is the main enemy of pellets after production. See our guide on how to store wood pellets.
9. Quality control
Good factories test samples from every batch for moisture, durability, fines, ash and calorific value, and send samples to independent labs. At Biomix Energy in Damietta, production is checked against international standards and our certificates are available online.
Frequently asked questions
Do wood pellets contain glue or chemicals?
Quality heating pellets contain only wood. The natural lignin in wood melts under pressure and binds the pellet. Some standards allow small amounts of natural additives such as starch, but no chemical glues.
Why are wood pellets shiny?
The shine comes from lignin that melts at the surface during pressing and hardens when the pellet cools. A glossy surface is usually a sign of good compression.
What wood is best for pellets?
Clean, debarked softwood such as pine and spruce is widely used because it has good lignin content and low ash. Hardwood pellets are also common and burn well.
How much sawdust makes one tonne of pellets?
Roughly 1.1–1.3 tonnes of dry material, or more of wet sawdust, depending on its starting moisture.
Need a quote from Biomix Energy?
We manufacture and export wood pellets, firewood, wood chips, charcoal, olive pits, animal bedding and alfalfa from our factory in Damietta, Egypt. Tell us the product, quantity and destination port and we will reply with specifications and a price.



